Selecting an awning for your 2013 CrossRoads Zinger Travel Trailer, you will need the bracket length (measure from the bottom to the top of one bracket) and the overall length (measure from the middle of one bracket to the middle of the other). If you have an awning installed currently, you have sufficient backing for replacing it. Depending on the siding and the tool, many times you can use a stud finder on an RV as well to identify mounting locations. These awning are typically installed... view full answer...
Looking through the models at that length it appears you'll be under 10,000lbs so the best option is going to be the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136. This system is fully automatic and can make stabilizer and leveling your trailer as easy as pressing a button and will have everything you need all in one kit. Because of this it is a bit steep price-wise.
If you're not looking to spend as much then you'd want to go with the Electric... view full answer...
Your 2011 Hyundai Santa Fe has a stock max tongue weight of 350 lbs. Many hitches will allow for more weight, for instance the Draw-Tite # 75684 is a confirmed fit for your vehicle with a rated tongue weight of 350 lbs without weight distribution or 500 lbs with weight distribution. This hitch is the only one we carry with a weight distribution system rating and you are already well over that with your dry tongue weight rating. If the vehicle were capable of the load then the hitch would... view full answer...
I wish it was possible to just replace the flip down clips you mentioned but at this time they are not available. Only solution is to go with the new head like you mentioned part # FA92-02-1255. view full answer...
The etrailer 3,200-Watt Portable Inverter Generator part # 333-0003 has a two year warranty for residential use and a 180 day warranty for commercial use. The warranty of the Firman inverter generators can vary depending on where it is purchased. view full answer...
The Equal-i-zer Weight Dist Shank part # EQ90-02-4600 should allow you to tow with the tailgate down on your 2017 Ram 3500. I have attached a photo for you of this shank used with a similar system on a similar truck view full answer...
Sounds like you're looking for the Replacement Lippert Garage Door Cable for Toy Hauler Patio Doors # LC39FR. This measures 121-1/4" long so you'll want to make sure that works for your application.
Please note that this cable is meant to basically hold a patio door in place. Not all toy hauler doors are able to be used as patios though so you'll need to make sure your door has a construction like the Lippert Patio Upgrade Kit # LC27FR and it wasn't designed to just be a ramp. view full answer...
Yes, since your current shackles are 2-1/2 inches the correct upgraded MORryde shackle kit would be the part # MR46ZR that you referenced. view full answer...
Our closest options for the seals you have pictured are part # SR43FR and # SR63FR. You'll want to take a quick measurement of the seals you have to ensure that these will match up and properly seal your windows. I've attached pictures of their dimensions below. view full answer...
It sounds like you're looking for a storage skirt for your 2013 CrossRoads Zinger 5th wheel trailer and there are two dimensions you'll want to know in order to find the correct one: the distance from the bottom of the overhang to the ground, and the length and width of the overhang portion of the trailer. We do have a couple options available that you can choose from, depending on the measurements you find.
- Adco Storage Skirt for 5th Wheel RV - Vinyl - White - 236" Long x 64" Tall... view full answer...
We have complete awning kits here at etrailer.
For your 2019 CrossRoads Zinger Travel Trailer, I was unable to find the specs of the stock awning. So, in order to choose the right one for you, you will need the bracket length (measure from the bottom to the top of one bracket) and the overall length (measure from the middle of one bracket to the middle of the other).
I've linked to a list of our awnings below, but a good one is the Solera 12V XL Power RV Awning - 15' Wide - Extra-Long... view full answer...
The Valterra Waste Valve Extension Tube with Handle # TX24HPB that you referenced is a 24 inch long extension tube that is designed for your situation. It gives you additional extension so that you can access the waste valves easier. It threads right on to the valve so it's an easy install as well. view full answer...
The diameter of your 205/75B14 tire is 26.1", and has a width of 8.1".
If you are needing a replacement tire I recommend the # AM1ST86 if you only want to replace one tire, or the # AM10235 if you are ok with replacing both tires.
The reason for this is the # AM1ST86 is a bias ply tire like your current tire, which you can tell by the B in the size between 75 and 14, where the # AM10235 is a radial tire. Radial and bias ply tires have a different sidewall construction making them not... view full answer...
The system likely bumped you up from the 10K Curt MV # C17062 to the 14K Curt MV # C17063 on account of the tongue weight. Tongue weight for a weight distribution system is a little different than trailer tongue weight as it handles both the loaded tongue weight of the trailer and any cargo sitting behind the rear axle of the tow vehicle.
If we use the 10% - 15% loaded tongue weight rule puts your loaded trailer tongue weight in the 948 lbs - 1,422 lb range, so add that with any cargo... view full answer...
We definitely have the parts needed to add brakes to your idler axle but we do not have them as a complete kit. What you'd need for hubs for your 2015 Crossroads Zinger 26DT is the part # AKHD-655-35-EZ-K which are pre-greased and then for brake assemblies you'd just need the # AKEBRK-35-SA for a set of left and right hand brake assemblies.
You'd want to use 10 gauge wire like part # 10-1-1 for wiring up the new assemblies. view full answer...
For the broken brake assembly the TruRyde kit part # TRU36FR would be your best option for a self adjusting brake set that comes with a replacement left and right hand side assembly. Then for replacement hub/drums you'd want the part # AKHD-545-35-EZ-K which comes with new bearings and seals. view full answer...
Yes the Optronics Flexible LED Light Strip # UCL90CB would replace your Carefree LED lights and would splice right to the same wiring of what you have now. view full answer...
In order to choose between the Dexter E-Z Flex Suspension Kits, part # K71-652-00 and part # K71-653-00 you simply need to measure the existing equalizers. If they measure 5-1/2" or close then you'll use part # K71-652-00 but if they measure 7-3/4" or close then you'll use part # K71-653-00. view full answer...
Since Atwood has gone out of business, their replacement parts are pretty hard to find.
With that being said, the:
-Replacement Crank Handle for Stromberg Carlson Landing Gear # LG-119226 will fit most Atwood jacks, however this crank handle will be quite a bit longer than your current handle. view full answer...
If your springs are essentially sitting totally flat they've stretched as far as possible basically. The best option we have would be the 3,500 lb leaf springs part # e54SR that you referenced. These are the right capacity and shorter than your stretched springs by enough that they would fit well. view full answer...